DIY Dollhouse Stair Railing From Scrap Materials (Easy Beginner Tutorial)
Once the staircase went into my Country Lane dollhouse, I was left with an open stair hole on the second floor that was just sort of . . . sitting there. Open. Waiting for a tiny person to fall through it . . . LOL So I made a simple stair landing railing using scrap materials I already had on hand and it ended up being one of the quickest little fixes of this whole build. Here’s exactly how I did this DIY dollhouse stair railing, measurements included.
Watch the Stair Railing Tutorial
What You’ll Need
- Railing trim, for the hand railing frame
- Miter shears, for clean 45 degree angled cuts
- Scrap wood for the side panels (foam board or thick cardboard work too)
- Wood glue, for joining the railing corners
- Super glue, or Aleene’s Tacky Glue if you’re more patient than me
- Wood putty, for filling seams and edges
- Stain for the railing and paint to match your room
- Sandpaper
- X-Acto Knife or miter shears, for cutting trim and scrap to size
- A ruler and pencil
Shop my Amazon Storefront for more dollhouse tools and supplies.
This post includes affiliate links and if you click and make a purchase, I might earn a small commission (at no extra cost to you), which helps me keep creating and sharing projects like this. View my full list of tools and materials I use for my dollhouse project here.
Step 1: Measure the Stair Hole
First, I measured the length and width of the stair opening on the second floor. Then I added a quarter inch to each measurement so the railing frame would sit just outside the edge of the hole instead of falling into it.
Step 2: Cut and Dry Fit the Railing Frame
Using those measurements, I cut my railing trim at 45° angles so the corners would meet cleanly, like a little picture frame. Before any glue came out, I dry fit the pieces around the opening to make sure everything lined up. Trust me, it’s a lot easier to recut one piece of trim now than to pry apart a glued corner later.
Once I was happy with the fit, I stained the railing pieces and glued the corners together with wood glue, then let it dry completely.
Step 3: Cut the Side Panels From Scrap Wood
With the railing dry, I cut scrap wood to fit inside it as the side panels. For my Country Lane, these were the measurements I ended up with:
- Short side: 2½” wide
- Long side: about 4¼” wide
- Height (both sides): just over 2½”
Please don’t copy these blindly! Every dollhouse has a slightly different stair opening and how you want your railing to sit will change things too. Measure your own before you cut.
I got lucky and one of my scraps was already the perfect width for the short side. For the long side, I fit two pieces in snugly, held them up against the railing to mark where there was extra, and trimmed off the excess.
If you don’t have scrap wood, that’s okay! Foam board or thick cardboard will work just fine for the panels, especially since they’re getting painted anyway.
Step 4: Join, Fill, and Paint the Panels
I sanded the two long-side pieces and super glued them together. Once the glue was dry, I filled the seam with wood putty so the panel would look like one seamless piece instead of two scraps pretending. Then I painted all the panels the same color I used on the room itself so they’d blend right in.
Step 5: Install the Panels Into the Railing
I glued the panels into the railing frame using super glue, mostly because I was impatient and wanted to see it finished. Wood glue or Aleene’s Tacky Glue will work just as well if you’re willing to wait a little longer for it to set.
Step 6: Finish the Edges for a Clean Look
I wanted this to look clean and built-in, like a landing in a real house. So I filled the sides with wood putty one more time, sanded everything smooth, and gave the whole area a final coat of paint. That last pass is what takes it from “craft project” to “oh, that’s part of the house.”
Setting It in Place
And that’s it! I simply set the railing on top of the landing next to the staircase. This was meant to be a super quick solution, so I may come back and update it later with actual spindles. If I do, you’ll see it here first.
For the full picture of this build, check out my Country Lane Dollhouse Kit Review & Build Guide.
Watch the full Country Lane Dollhouse Build
More Country Lane Resources
- Country Lane Dollhouse Kit FAQ
- How to Wire a Dollhouse for Electricity (Cir-Kit 101 Kit)
- Every Product & Tool I Used
- Prepping & Sorting Your Pieces Before You Build
- Dry-Fitting and Assembling the House Body
- Adding Trim & Batten to the Front Door
- Painting the Exterior, Trim & Details
- How to Shingle the Roof
- How to Stain Dollhouse Shingles After They’re Already on the Roof
- How to Remove a Glued Dollhouse Roof With a Hair Dryer (No Damage)
- Finishing the Chimney: Cobblestone, Faux Grout & Aging Technique
- Attaching Trim, Shutters, Flower Boxes & the Staircase
Build alongside us in Lina’s Dollhouse Collective
If this build feels lonely, that is exactly what the Collective is for. Lina’s Dollhouse Collective is the Facebook group where we share ideas, put the free tools to work as part of our process, and cheer each other on through every glued finger and crooked shingle.
Inside the group you can ask the questions you do not want to post publicly, show off a build at any stage (the messy ones too), and pick up tricks the rest of us learned the hard way. We talk scale, paint, wiring, sourcing, kits, scratch builds, and yes, snack recommendations for long glue-drying breaks.
Bring your tools. Bring your scale ruler, your color palette, and your scale conversions. Bring your wins and your roadblocks. We will meet you there.

Join the Collective
Stay up to date & receive the latest posts in your inbox.
Privacy Policy